AIRXCEL 48000 SERIES DIMENSIONS
Please use our Product Literature Search to find the right documents for your model. Temporarily remove the air grille assembly filter door. Box Wichita, KS Web: The ability of an air conditioner to cool down a vehicle or maintain a consumer desired temperature is dependent upon the heat gain of the vehicle. The pointed end nose of the shroud must face towards the front of the vehicle. Please be patient and I will get to you shortly. It is not a substitute for a furnace. Setting the temperature on the thermostat so low the compressor does not cycle off and on.
Install Air Grille Assembly. Some upper unit mount gaskets have a locater block on each side to locate the divider board. The product consumer should also be afforded the opportunity to purchase the optional three 3 year parts replacement contract available from Airxcel, Inc. Peel the release liner from the adhesive strip around the opening. Make certain that all wires are pushed into the control boxes or laying in the wireway between the thermostat and switch boxes and will not be pinched by the control box shield. Installez les boutons de commande sur les tiges de commutateur et de thermostat. Installing the Roof Top Unit.
Fixation du climatiseur au toit. The ceiling plenum bolts below the roof top unit.
Carefully wedge this divider between the walls of the roof opening and up against the upper unit basepan with the silver seres facing forward. Insure that the connector snap-locks into position. Indoor and outdoor temperatures may be too cold lack of heat. Tighten set screw to secure the assembly so as to prevent movement.
It depends mostly on your trailer and its insulation and openings. Capable of supporting both the weight of the roof top air conditioner and the interior ceiling assembly. All field fabricated cold air supply ducting must be insulated dimensoons must have a vapor barrier.
Hopefully the roof is white or silver to reflect as much heat as possible.
The front two screws should pass through the clearance holes in the metal control box shield See Figure 9. Circuit Protection — Refer to upper unit nameplate.

Remove ceiling assembly from carton, separate individual items and remove the two grilles and filters from the ceiling shroud. If the roof of the vehicle is sloped not level such that the roof top air conditioner cannot be mounted within the maximum allowable degree deviations, an exterior leveling shim will need to be added to 48000 the roof top air conditioner level.
Installation and service personnel are required by some states to be licensed.
Holes For Wires 14″ If a roof vent opening is not used, a new opening See Figure airccel will have to be cut into the vehicle dimeneions. A matching opening will also have to be cut into the interior vehicle ceiling. Registers Supply cold air registers should have a minimum discharge area of 48 square inches per system, or 24 square inches per duct.
Attach the duct locater plate to the mount frame using 4 short screws found in the small parts package. Securing the Air Conditioner to the Roof.
Roof Top Product Selector
Follow the steps below to secure the air conditioner to the roof. The use of components not tested in combination with these units will void the warranty, may make the equipment in violation of state codes, may create a hazard and may ruin the equipment. FIGURE 4 6 Proper tension dimensjons been achieved for each bolt when any portion of each gasket indicating tab has been pulled down even with the roof.
![]()
Electrical problems, faulty thermostat, inoperative freeze thermistor. A minimum of 6 is recommended. The ceiling plenum must be installed under the roof opening. If used, the extension cord should be sized to airxcle proper voltage at full load conditions. Truck with Camper — airxcek should be between 4 or 5 feet from the rear of the camper to achieve maximum cooling effect. The low temperature probe monitors the temperature of the air conditioner evaporator coil.
Coleman Mach – Roof Top Product Selector | Airxcel
All manual controls have been removed from the ceiling plenum. Install the ceiling assembly mount frame using the four bolts found with the ceiling assembly. Insert the two-pin connector of the heater umbilical into the receptacle on the control box. Additionally, the outdoor air temperature, humidity, air volume and even proper air conditioning maintenance all have an effect on the air conditioner supply air temperature. Plug the air conditioner electrical conduit into the 9 position receptacle as shown in Figure A typical leveling shim is shown in Figure 3.
